Clik here to view.
Music Thing AxoControl / Axoloti Full DIY Kit
A full kit containing all parts to build the unit shown in photographs. The Axoloti core board can be provided optionally. You just need to provide the tools, solder, computer and USB power supply! (An...
View ArticleClik here to view.
AT-AT-AT – Triple Attenuator Eurorack Kit
A kit for a Eurorack passive triple attenuator module (4hp). A very simple and very useful Eurorack DIY kit. Below you’ll find links to very thorough build instructions written with synth DIY beginners...
View ArticleClik here to view.
Sonic Potions ‘Penrose’ Quantiser Full DIY Kit
Penrose is a simple CV quantizer DIY kit for the eurorack format. It takes an incoming continuous CV voltage and converts it to the nearest note in a scale. Active notes can be selected with the 12...
View ArticlePolaxis TALKO DIY Kit
THIS IS A FULL DIY KIT This module is performing real-time LPC synthesis to produce intelligible voice or … not if you choose to. The module produces sounds in 3 major modes: Speech, Repeat and VCO. In...
View ArticleMusic Thing Modular – Turing Machine Expander VOLTAGES Kit
This kit includes everything you need to build a fully functioning expansion module apart from the tools and solder. Comes with 12hp Aluminium Eurorack panel. Thonk build documentation is here –...
View ArticleNLC – Sloth – Panel and PCB
This is a very simple to build chaos module that can be built in 2 ways: slow or VERY slow. Slow means 1 cycle every 15 seconds, VERY slow is 1 cycle every 15 minutes. It can take up to an hour for...
View ArticleNLC – BOOLs – Panel and PCB
“These are nice. The inputs can be any signal crossing 1V. The logic outputs give 5V gates that are all related to each other as made up of different input combinations. The S&H input can be a...
View ArticleMusic Thing Modular – Turing Machine Mkii Full DIY Kit
This kit includes everything you need to build the Mkii version of the Turing Machine. You just need to provide the tools and solder. Comes with 1ohp Aluminium Eurorack panel. Since it was launched in...
View ArticleCGS PCBs (DUSG, Serge Filter etc)
Three extremely useful little synth utility PCBs for DIYers LED Driver (strip of 11 pieces) – CGSLD – Info, BOM etc. NEW! – Real Ring Modulator- CGSRR – Info, BOM etc NEW! – Psycho LFO – CGS03 – Info,...
View ArticleMusic Thing Modular – Turing Machine Expander VACTROL MIX Kit
A full kit to build the VACTROL MIX expander for the Turing Machine MK i and MK ii. This module will not function without a Turing Machine attached. Vactrol Mix combines four audio or CV signals into...
View ArticleClik here to view.
Non Linear Circuits PCBs
Non Linear circuits are responsible for some of the most original and truly forward thinking analog designs for modular synths in the past few years. Andrew the designer describes it thus: ANALOGUE...
View ArticleClik here to view.
Music Thing Modular – Radio Music Full DIY Kit
V2.1 PCB set, one minor fix – some users had found the switch a little tight to fit. This is a full kit which includes every single component to build a Radio Music module right down to the Teensy...
View ArticleAntumbra EURD PCB
A little PCB to allow anyone to easily create Arduino based Eurorack projects. It has a power source with 5V regulator, all Arduino pins routed out to header pins, neatly organized. It’s also easy to...
View ArticleDavies Skirted Knobs
Available in black only. These are genuine Davies Molding parts for 1/4″ or 6.35mm diameter pot shafts. 1913BW : Bold Large (1.12" / 28.45mm diameter) 1910CS : Bold Small (0.75" / 19.05mm diameter)...
View ArticleGrayscale Panels
Note we now carry the Rogan knobs that Greyscale sell here too. Grayscale panels are 1.6mm thick anodized aluminum Metalphoto panels.
View ArticleClik here to view.
‘Make Noise’ + ‘Mutable’ Style Knobs
These PT range knobs are made in the USA by Rogan, they are not official Mutable Instruments or Make Noise products, but are the same style from the same factory.. PT-1PS: small white pointer knob (all...
View ArticleTsyklon Labs – Chaos Divider
CHAOS DIVIDER HV Eurorack Clock Modulator Module A video posted by Cory Sterling (@redstripedown) on Jul 5, 2016 at 2:08pm PDT A clock signal. A serial chain of pulses. Some wide, some narrow. Some...
View ArticleEntrospec IUNGO – Full DIY Kit
Iungo is designed to bridge the worlds of modular synthesizers and MIDI controlled instruments. This module lets you create both monophonic and polyphonic sequences to play your MIDI gear, all...
View ArticleClik here to view.
Music Thing Modular – Turing Machine T-Shirt
Gildan Premium Cotton Ring Spun T-Shirt ‘Sports Grey’ Colour Screenprinted on front. Printed in Wales, UK Custom Thonk nape print Custom Thonk sleeve tag Fabric 100% ring-spun Cotton pre-shrunk jersey...
View ArticlePeter Blasser – Ciat Lonbarde – PCBs
These PCBs are all Peter Blasser/Ciat Lonbarde designs which have been put to new PCB layouts by Meng Qi. Please note these are not beginner projects, all the information we have available is listed...
View Article