ADDAC213 Eurorack Bridge – Full DIY Kits
The ADDAC213 Bridge acts as a simple one-cable bridge system between different areas of a case or different cases. The ADDAC213A modules can send & receive 8 CV or audio signals between your cases...
View ArticleShakmat Modular – Knight’s Gallop – Full DIY Kit
Math & Rhythm Two outputs and five different rhythmic flavors multiply by a load of “algo-rhythmic” processing to result in a practically infinite number of polyrhythms. That’s the fundamental...
View ArticleShakmat Modular – Time Wizard – Full DIY Kit
The Shakmat Modular Time Wizard is an 8HP sextuple clock divider. The module features individual division control for all six outputs and there are different division options available depending on...
View ArticleClik here to view.
Techspray ProWick #4 Desoldering Braid
Desoldering braid (wick) is pre-fluxed copper braid that is used to remove solder, which allows components to be replaced and excess solder to be removed. For the fastest wicking action, rosin flux...
View ArticlePolaxis TALKO DIY Kit
THIS IS A FULL DIY KIT This module is performing real-time LPC synthesis to produce intelligible voice or … not if you choose to. The module produces sounds in 3 major modes: Speech, Repeat and VCO. In...
View ArticleClik here to view.
4MS Eurorack Power
NOT A DIY PRODUCT – BUILT AND TESTED BY 4MS IN PORTLAND, OR, USA Row Power is a clean, regulated, and protected power solution for eurorack systems. Row Power 30 provides 30W of power, suited for any...
View ArticleClik here to view.
CLIFF ‘CL1384’– 3.5mm Jack Sockets
The CL1384 is a 2-way right-angle PCB mount, mono switched 3.5mm Jack. Each jack is supplied with it’s own separate Hex Nut. These jacks are commonly used on Doepfer modules. The transparent jacks...
View ArticleClik here to view.
RYO Airtenuator x3 – Full Kit
The RYO Airtenuator is a floating passive attenuator you connect between two modules in your rack via patch cables, acting as a volume/modulation depth control between the source and destination....
View ArticleRYO Penta Sequencer Kit
Penta The RYO Penta is a compact 4hp sequencer for eurorack that’s easy to build and low cost, without compromising on our usual quality standards such as buffered output, schmitt triggers on inputs...
View ArticleRYO Paths – Full kit
PATHS – A Cycling Sequential Switch A 4:4 cycling sequential switch, featuring simultaneous forward/reverse stepping, hold, reset, and an additional voltage controlled mode based on the same design as...
View ArticleClik here to view.
God’s Box ‘Humpback’ Filter. Panel/PCB Set
The God’s Box ‘Humpback’ DIY module is produced exclusively in collaboration with Thonk. The module is 8hp wide and is skiff friendly; 38mm deep. Contents Aluminium 8hp Eurorack panel – High Quality...
View ArticleClik here to view.
God’s Box ‘Humpback’ Filter. FULL DIY KIT
The God’s Box ‘Humpback’ kit is produced exclusively in collaboration with Thonk. This kit includes everything you need to build the module apart from tools and solder. The module is 8hp wide and is...
View ArticleRochester – CA3080AE IC – Reissued OTA Chip
These are genuine DIP8 – CA3080AE OTA Chips, made by Rochester Electronics. It was thought that the CA3080AE was to become obsolete after Intersil announced they would discontinue manufacturing,...
View ArticleMusic Thing Modular – Turing Machine Mkii Full DIY Kit
This kit includes everything you need to build the Mkii version of the Turing Machine. You just need to provide the tools and solder. Comes with 1ohp Aluminium Eurorack panel. Since it was launched in...
View ArticleTouellSkouarn Skorn Da Bask – Full DIY Kit
Assembly Guide – Skorn Da Bask Build Document Drone & Abstract Rhythm Generator – The Skorn Da Bask is composed of three analog sawtooth oscillators and a Resonant Low-Pass Filter. As well as...
View ArticleClik here to view.
TouellSkouarn Strakal Brulu – Full DIY Kit
Build Document here. This is a full kit which includes everything you need to build a working Eurorack Module, Panel, PCB, all components, knobs jacks, power cable, rack screws. 8hp / Red ink...
View ArticleTouellSkouarn Sonveskan – Full DIY Kit
Assembly Guide – Sonveskan Build Document The Sonveskan is a three-channel feedbacker /mixer – utilising germanium transistors. Each audio path comes equipped with individual gain control, voltage...
View ArticleBASTL KASTLE – Full DIY Kit
Kastle is a mini modular synthesizer with headphone output, 2 in/out ports for interfacing other gear and it runs on just 3 AA batteries. It is DIY friendly and ideal for beginners in modular...
View ArticleRYO Penta Sequencer Kit
Penta The RYO Penta is a compact 4hp sequencer for eurorack that’s easy to build and low cost, without compromising on our usual quality standards such as buffered output, schmitt triggers on inputs...
View Article