SSSR Labs ‘Kotelnikov’ VCO – DIY Minimal Kit
This DIY Minimal Kit contains the following parts only: Kotelnikov PCB Set Kotelnikov 14HP Eurorack Aluminium Front Panel Pre-Programmed ATMEGA Chip feat. latest V1.1 Firmare КР590КН5, AD7545 &...
View ArticleSSSR Labs ‘Kotelnikov’ VCO – Full DIY Kit
The Kotelnikov is a Eurorack voltage controlled digital wavetable oscillator module with morphing features and built-in transient generator. This oscillator can generate a wide range of sounds with...
View ArticleSSSR Labs SM010 ‘Matrixarchate’– Full DIY Kit
The SSSR Labs Matrixarchate is a 16×8 input-output sequential matrix signal router, capable of connecting various signal sources to destinations and storing this connection matrix in up to 60 user...
View ArticleSmall Fluted Knobs
BULK DISCOUNT | 10+ – 5% | 25+ – 7% | 100+ – 10% | 500+ – 20% | (Bulk prices are calculated once items are added to your cart) Cream knob as used on RYO modules Round shaft knobs made with high...
View ArticleClik here to view.
Davies 1900h Clone
BULK DISCOUNT | 10+ – 5% | 25+ – 7% | 100+ – 10% | 500+ – 20% | (Bulk prices are calculated once items are added to your cart) Pair with the new MXR knob in the same colour range. New Black 1900h...
View ArticleAnalogue Research Eurorack Serge Dual Processor – Full DIY Kit
ARC’s Serge Dual Processor (SDP) is an officially licensed Eurorack implementation of the original processor module designed by Serge Tcherepnin for his Modular Music System in the 1970s. The Dual...
View ArticleAnalogue Research Eurorack Serge Audio Mixer – Full DIY Kit
ARC’s Serge Audio Mixer (SAM) is an officially licensed Eurorack implementation of the original mixer module designed by Serge Tcherepnin for his Modular Music System in the 1970s. The Audio Mixer...
View ArticleClik here to view.
Sonic Potions ‘Penrose’ Quantiser Full DIY Kit
Penrose is a simple CV quantizer DIY kit for the eurorack format. It takes an incoming continuous CV voltage and converts it to the nearest note in a scale. Active notes can be selected with the 12...
View ArticleClik here to view.
11mm Hex Standoffs
Standoffs are sold in packs of TEN These are 11mm long, M3 female to female Hex Standoffs made from Steel with Zinc plating. These are the same parts used in Thonk kits and specced for many Eurorack...
View ArticleKlavis – NoDrain +5V Source
The Klavis NoDrain adapter is intended for Eurorack cases lacking a dedicated 5 volts supply. It draws its power from the negative 12 volts rail – reclaim your unused watts! Did you know that typical...
View ArticleControl ‘Camo’– Eurorack Patch Cables
The Control Cable is a 3.5mm (1/8″) patch cable for use with Eurorack modular synthesizers. The narrow diameter barrel size was designed specifically for patching into tight narrow jack spots and a low...
View ArticleClik here to view.
LPZW.Modules – PO-Series Eurorack Adaptor PCB
This PCB is designed to adapt the Teenage Engineering Pocket Operators for use within Eurorack. This adaptor PCB has the following functions: • hold the PO in your Eurorack Case • supply power to the...
View ArticleClik here to view.
LPZW.Modules – PO-Series Eurorack Adaptor – DIY Kit
Adapt a Teenage Engineering Pocket Operator for use as a 12HP Eurorack module. This DIY Kit comes with all SMD components already pre-soldered and contains all the other components needed to build the...
View ArticleBubblesound Mix6 – Full DIY Kit
Build your own MIX6 with the MIX6 DIY Kit – The surface mount soldering on this kit comes pre-soldered so you just need to solder the jacks and pots and assemble. The 6X1(3X1) is a dual 3...
View ArticleBubblesound SeM20 VCF – Full DIY Kit
The SeM20 is a 2-pole state variable filter loosely based on the Oberheim SEM filter, but with the resonance section of the MS20 grafted on for an extra bit of grit! It won’t self oscillate usually,...
View ArticleBubblesound VCOb – Full DIY Kit
The VCOb is a voltage-controlled analog oscillator based around a classic triangle core VCO. The range of the VCOb is one of the widest in the analog modular world. And like all triangle cores the...
View ArticleBubblesound uLFO – Full DIY Kit
The uLFO is an voltage-controlled analog low frequency oscillator based around a classic triangle core VCO running through a series of waveshapers, giving the user an extremely wide range of outputs...
View Article‘Erica Synths’ style Knobs – 6.35mm Shaft
These are the exact style knobs as used in all Erica Synths DIY Kits. These knobs are similar to our MXR range but with slightly sharper edges, they fit great on our 6.35mm Alpha Pots. Large Knob...
View ArticleClik here to view.
Fonitronik TH VCO MAXIMUS Panel/PCB set
Back in 1987 Thomas Henry published the CEM3340 based Deluxe VCO in his book Build A Better Music Synthesizer. Alas, in the following years everything went digital and the CEM chips went out of...
View Article