Clik here to view.
Olitronik Circuits – Micrón Synth Voice – Full DIY Kit
The Micrón is a newly designed complete analog synthesizer voice in just 8HP! The module has a fully featured VCO with Saw/Pulse outputs, FM input and voltage controlled PWM. There is also a Sync...
View ArticleEurorack SERGE Sequencer 8 XL (SEQ8XL) Full DIY Kit
THIS IS A FULL DIY KIT SERGE MODULAR FOR EURORACK – Under licence from Serge Tcherepnin “Serge Modular” is an analogue modular synthesizer system developed by French composer and electronic designer...
View ArticleADDAC214 VC Rotator – Full DIY Kit
The ADDAC214 VC Rotator is a stepped routing module for audio, CVs, gates and triggers! A typical VC switch can only switch one source to multiple destinations, or multiple sources to one destination...
View ArticleFSS – Brunswick Synthesizer – Full DIY Kit
The Brunswick is perfect for those who want an introduction into the world of patchable analogue synthesis! The Brunswick Synthesizer from Future Sound Systems is a newly designed, affordable synth...
View ArticleControl ‘Camo’– Eurorack Patch Cables
The Control Cable is a 3.5mm (1/8″) patch cable for use with Eurorack modular synthesizers. The narrow diameter barrel size was designed specifically for patching into tight narrow jack spots and a low...
View ArticleGinkosynthese – Grains – Full DIY Kit
A DIY eurorack module! This complete and easy-to-build DIY kit is one of the cheapest ways to get a voltage controlled oscillator in your modular and sounds completely different than all other...
View ArticleClik here to view.
Ginko Synthese – MIC- Full DIY Kit
The Ginko Synthese MIC is a Eurorack microphone pre-amp module in 2HP! This module was designed to sit alongside the Ginko Sampleslicer but can be used as a monophonic microphone preamp to take signals...
View ArticleGinko Synthese – EZSQ – Full DIY Kit
The EZSQ is a simple 8 step sequencer featuring a clock input, reset input and pitch output. It was designed to sit next to the VCSQ2 to give it even more power, but 8 steps sequencers are useful...
View ArticleClik here to view.
Control – 1/4″ to 1/4″ Instrument Cable
1/4″ to 1/4″ shielded TS cable. Meant to be used with instruments that use 1/4″ jacks such as guitars, pedals, mixers, etc. Comes packed in a circular wrap style to prevent kinks. Control logo embossed...
View ArticleClik here to view.
Control – 3.5mm to 1/4″ Adaptor Cables
3.5mm TS to 1/4″ TS cable available in four sizes and two colours. Meant to be used to connect your modular synth or other gear that uses 3.5mm jacks to gear that uses 1/4″ jacks such as external...
View ArticleCornfield Electronics – ArduTouch Synthesizer – Full DIY Kit
The ArduTouch is a new Arduino-compatible music synth kit. It’s fully open source – everything you need to put this together is available on the ArduTouch GitHub. The ArduTouch is similar to the...
View ArticleClik here to view.
Flight of Harmony – IMP Full DIY Kit
The IMP is a tonal noise generator designed to bring ethereal voices, growling drones, abrasive and tonal noise to your Eurorack format modular. How does the IMP produce such a wide palette of sounds?...
View ArticleClik here to view.
KOMA Elektronik – STROM MOBILE – Portable Power Supply
Strom Mobile is a portable power solution for music makers and everyone who needs reliable voltage source at all times! The Strom Mobile transforms the output voltage of USB power banks (5V DC) to...
View ArticleEurorack Serge ÷NCOM Full DIY Kit
THIS IS A FULL DIY KIT This is the latest revision PCB – All SMD components are already professionally reflow soldered in – This project requires a small amount of through-hole soldering only. SERGE...
View ArticleClik here to view.
Eurorack Serge Resonant EQ Full DIY Kit
THIS IS A FULL DIY KIT SERGE MODULAR FOR EURORACK – Under licence from Serge Tcherepnin “Serge Modular” is an analogue modular synthesizer system developed by French composer and electronic designer...
View ArticleEurorack Serge Variable SLOPE (VCFS) Full Kit
THIS IS A FULL DIY KIT It contains all components required for a complete build, right down to rack screws and power cable. We selected and used the parts as specced by Random*Source. Random Source...
View ArticleClik here to view.
Befaco – Hexmix System – Full DIY Kits
Recommended for experienced builders only, please read the build docs before purchasing. These are DENSE builds. Hex Mix – 6 Channel Mixer The Hexmix System is a six channel performance mixer...
View ArticleWorng Buff Test – Panel/PCB set
This project has surface mount electronics (SMD) No Parts are provided. The Bufftest is an extremely accurate buffered mult with a clever little circuit that lets you turn it into a cable tester at the...
View ArticleADDAC305 Manual Latches Full DIY Kits
The ADDAC305 Manual Latches is a combination of 8 manual latching switches in a small and elegant module: each button toggles between Gate high or Gate low when pressed, outputting a +5V gate signal....
View ArticleADDAC304 Manual Gates Full DIY Kits
The ADDAC304 Manual Gates features eight gate outputs (0 +5v) which are manually activated via eight dedicated pushbuttons on the frontpanel – a perfect way to perform on and control your modular...
View Article