Clik here to view.
Zlob Modular – Skew Fade LFO Full DIY Kit
The Skew Fade LFO is a 3HP all analog low frequency oscillator capable of a plethora of waveforms. It has three rate settings – with a range that goes down to 3 minutes and 30 seconds a cycle, up to...
View ArticleClik here to view.
Zlob Modular – Entropy – Panel / PCB Set
Entropy is an all analog random voltage and noise generator with a number of outputs and options. It features sample/track and hold normalled to white noise with a toggle switch for selecting either...
View ArticleClik here to view.
Zlob Modular – Entropy – Full DIY Kit
Entropy is an all analog random voltage and noise generator with a number of outputs and options. It features sample/track and hold normalled to white noise with a toggle switch for selecting either...
View ArticleClik here to view.
Ginko Synthese – MIC- Full DIY Kit
The Ginko Synthese MIC is a Eurorack microphone pre-amp module in 2HP! This module was designed to sit alongside the Ginko Sampleslicer but can be used as a monophonic microphone preamp to take...
View ArticleClik here to view.
Ginkosynthese – Sampleslicer v2 – Full DIY Kit
Version 2 of the Samplslicer adds a gain input potentiometer and a switch for pitch mode so you don’t have to restart your modular to get into a different pitch setting. This new version is also a...
View ArticleClik here to view.
Dreadbox Lil’ Erebus – Eurorack Full DIY Kit
The Lil’ Erebus is an analog paraphonic Eurorack full synth voice based on the original Dreadbox Erebus. The module features two oscillators with individual level and tune controls which you can...
View ArticleClik here to view.
3 x Floating Star Multiple
A pack of three, six-way, Befaco-branded multiples. These are passive multiples with six 3.5mm sockets.
View ArticleTsyklon Labs – Eurorack Cable Tester Full DIY Kitl
If you are a DIY Synth novice, this is a great and useful bit of kit to strengthen your DIY skills. If you are a veteran [or, as they like to say at Tsyklon Labs – “Hero of Synthesizer DIY”], then this...
View ArticleCornfield Electronics – ArduTouch Synthesizer – Full DIY Kit
The ArduTouch is a new Arduino-compatible music synth kit. It’s fully open source – everything you need to put this together is available on the ArduTouch GitHub. The ArduTouch is similar to the...
View ArticleClik here to view.
God’s Box ‘Lollipop’ Compressor. FULL DIY KIT
The Lollipop is a studio grade dual-mode analog mono compressor designed specifically for Eurorack. Two different compression modes – FET and Vactrol – give two different flavours of compression....
View ArticleClik here to view.
God’s Box ‘Loose Fruit’ WaveShaper. FULL DIY KIT
Loose Fruit packs two waveshapers and a crossfader combined into one module and is designed for sculpting rich harmonic timbres. Originally intended for use with ‘single note’ waveforms including...
View ArticleClik here to view.
Olitronik Circuits – Micrón Synth Voice – Full DIY Kit
The Micrón is a newly designed complete analog synthesizer voice in just 8HP! The module has a fully featured VCO with Saw/Pulse outputs, FM input and voltage controlled PWM. There is also a Sync...
View ArticleClik here to view.
Dreadbox Lil’ Erebus – Eurorack Full DIY Kit
The Lil’ Erebus is an analog paraphonic Eurorack full synth voice based on the original Dreadbox Erebus. The module features two oscillators with individual level and tune controls which you can...
View ArticleADDAC200PI Pedal Integrator – Full DIY Kit
This small utility is the pedal’s lover best friend, it allows 2 different chains of pedals to be independently connected to your modular synthesizer. The Send channels attenuate the synth level to...
View ArticleClik here to view.
Music Thing Modular – Mikrophonie Contact Mic Module
IF YOU WANT TO JUST BUY THE NEW PANEL DESIGN ON ITS OWN GO HERE Build Manual This kit contains all parts to build the module, right down to the power cable and the screws. These kits ship with a...
View ArticleShakmat Modular – Time Wizard – Full DIY Kit
The Shakmat Modular Time Wizard is an 8HP sextuple clock divider. The module features individual division control for all six outputs and there are different division options available depending on...
View ArticleTransient Modules – 1F Switch – Full DIY Kit
The Transient Modules 1F is a voltage controlled switch, intended to be a friend for your sequencer. The 1F features two inputs – labelled IN and CV, the CTRL input switches the output from IN to CV...
View ArticleTransient Modules – 4R Random – Full DIY Kit
The 4R is a quad random voltage generator in just 2HP. The 4R generates two different random stepped voltages per input each time a rising edge is sensed at TRIG1 or TRIG2. The inputs are independent...
View ArticleErica Synths ‘BBD Delay / Flanger’– DIY Partial Kit
Note: This partial DIY kit contains the following parts only: BBD PCB Set BBD Eurorack Front Panel (14HP) V3205SD IC V3102 IC PCB connectors Erica Synths Knobs can be purchased here:...
View Article